DIY, Halloween, New Artwork

Tiny Hylian Shield Tutorial Part TWO: Steps 6 through 10

Yesterday I started showing you how to make your own tiny Hylian Shield from the Legend of Zelda Ocarina of Time. Today I am back to finish up the tutorial.

Step 6: Detailing What would the Hylian Shield be without its fine detailing? A Deku Shield? There are a lot of options for adding details to the center of your shield. With this smaller shield, I chose to use a combination of materials. For the Triforce, I used some thin cardboard. For the bird motif, I used my hot glue gun to paint the design. If you are not very good at freehand-drawing, I would suggest cutting out the design from your template. This was a little tricky, but I am pleased with the results. I may try something different on the larger shield, though.

Tiny Hylian Shield Tutorial 8

The glue gun added a nice texture, but was difficult to control.

Step 7: Prime This is especially important if working with cardbard. The dark surface will be difficult to paint if you do not prime it.

Tiny Hylian Shield Tutorial 9The front after one coat of primer.

Be sure to get the front and the back. Let it dry completely between coats if a second coat is necessary.

Tiny Hylian Shield Tutorial 10The back of the shield after one coat of primer.

Step 8: Spray Paint Now it’s time for the fun part. Once you’ve let your coat of primer dry completely, you can add a coat of your Hammered Spray Paint. This paint is textured and does a great job of covering most surfaces evenly. I did not have any problems with my shield, but you may need to touch-up or add a second coat of paint. Be patient and let each coat dry before applying the next one.

Also, if you did cover the outside of the shield with masking tape, bear in mind that the paint will remain tacky there for a little while longer than it does on the cardboard. Be mindful of this when setting the shield down on surfaces while it dries.

Paint both sides of the shield.

Tiny Hylian Shield Tutorial 12Shield front after one coat of Hammered Silver paint.

Step 9: Paint and Detail. Once your silver paint has dried, it is time to add detail to the shield. I used a variety of small brushes and my acrylic paints to add the color to the front of the shield. I did the blue base first and then painted the red bird and Triforce, leaving the silver parts

Tiny Hylian Shield Tutorial 13

Carefully adding blue paint.

Tiny Hylian Shield Tutorial 14

Don’t forget to paint the back!

You may need to add several coats of paint. Depending on the type of paint you are using, you may also want to cover the shield in a clear gloss coat. As all of my paints were glossy, I did not do that for my shield. Once the paint has dried on the front and the back, it is time to add some hardware. On this small shield, I added a little loop to be used to hang or secure the shield. On a standard-size shield, it is even more important to add the correct hardware. This small loop will do for now, but if you make a larger shield in the future, be sure to make the straps and handle more secure.

Tiny Hylian Shield Tutorial 15

Brads have proven to be very useful for this project.

Step 10: Sit back and admire your handy-work. Even if you have never touched a tool in your life, this project can be easy enough for any skill level. While this shield may not be big enough to defend yourself from even the smallest of Deku Shrubs, it is cool enough to display in your home or office. Many materials are ones that you may have on-hand.

17

Tiny Hylian Shield Tutorial 16

With the leather loop on the back, you can easily hang this small shield somewhere where it can be seen!

I hope this tutorial was helpful! If you have any questions regarding the instructions or photographs please let me know. Share your finished projects too!!!

Want to see STEPS 1 – 5? Click here!

DIY, Halloween

Tiny Hylian Shield Tutorial Part One: Steps 1 through 5

The other day I mentioned that I would be working on a DIY tutorial project. For those of you who guessed that I would be making a Hylian Shield, you are right! Congrats! I am going to be Link for Halloween, and I thought now is as good a time as ever to try my hand at writing an online tutorial for like-minded gamer girls!

Tiny Hylian Shield Tutorial 5

Now, I am a rather practical and analytical person. I love working with new or challenging materials. Initially I had wanted to make my shield out of wood, but without a proper workspace, shared walls, and older neighbors, I thought that may prove to be too messy and noisy. I have worked with wood before, but always in a proper workspace like a garage or studio. I was also taught to “measure twice, cut once,” so I decided to make a small-scale version of the shield to get the materials and measurements right. These instructions will be for how to make a small “display” Hylian Shield measuring approximately 6.5 inches by 5.5 inches (16 x 14 cm).

Step 0: Decide which version of the Hylian Shield you would like to make. For the small shield I chose to make the shield from the Legend of Zelda Ocarina of Time. For my larger shield, however, I will be using the designs from the Legend of Zelda Twilight Princess.

Step 1: Gather your materials:

Supplies

YOU WILL NEED:

Cardboard (in large unbent pieces): I sourced mine from my local grocery store.

Newsprint: (or other scrap paper) to make your template drawings. Or print them out from images you find online. Be sure to make drawings for the front of the shield AND for the back of the shield.

Pencils and Bold Markers to make your drawings on the newsprint and on the cardboard

Brads: buy a lot of them, I went through close to 75 of them

Glue: I used Aleene’s Tacky Glue and it worked quite well

Masking Tape: .5 inches to 1 inch wide

Rust-oleum “Hammered” silver spray paint

Rust-oleum Primer (White)

X-Acto #11 Blade and Knife

Scraps of Leather or other durable brown fabric

Paint and Paintbrushes I used Martha Stewart’s High Gloss Acrylic Paints and an assortment of brushes

Measuring tools: Ruler, compass, protractor, measuring tape, etc.

Step 2: Make the shield base. Take your template drawing and trace it out on the cardboard three times.

Tiny Hylian Shield Tutorial 1

Make sure you leave a little room around each piece to be able to cut safely.

This will create the piece for the front of the shield, the body of the shield, and the detailing for the back of the shield. Once you have traced and cut out the three pieces, cut out the outside boarder for the front of the shield. Use your template and cut out the inside design of the shield, leaving just the boarder as shown in the image below.

Tiny Hylian Shield Tutorial 4This will help give the shield more depth.

Step 3: Cut out the front and back pieces. Use your Xacto Blade to carefully cut around your templates to make the front and the back of the shield.

Step 4: Secure the shied pieces together. Using brads and glue, you will be making sure that this shield is as durable as possible. It is important to measure out where you want your brads to go to adorn both the front and back of the shield. They add a nice aesthetic, but they also serve to keep the several pieces of the shield from separating. I measured out the places where I wanted to put the brads and marked them with pencils. I found the brads were easier to push into place when I made a small cut with my blade as shown in the image below.

Tiny Hylian Shield Tutorial 6

Sandwich the pieces together and use some of your glue of choice to make sure the pieces don’t go anywhere. I found it helpful to add a little glue to the hole where the brad was placed too.

Step 5: Tape it up. Once all the pieces are sufficiently glued together and brads are placed, flip the shield over and view from the side. Here is the downside of using corrugated cardboard: The edges are rough and porous. You will want to use your masking tape and run it around the outside of the shield. This will give the edges a finished look and will protect your shield from damage on the side. Trim the corners so that the tape does not bunch up too much.

Tiny Hylian Shield Tutorial 7

You could also fill the holes with hot glue, but the tape is easier and cheaper.

Tiny Hylian Shield Tutorial tape

The shield with 1/2 inch masking tape around the edges.

The tape adds a nice finished edge without taking away from the shield itself. It also protects the sides and keeps gunk from getting in there. Stay tuned next time for how to complete your shield!

Uncategorized

New Legend of Zelda Buttons

“It’s dangerous to go alone! Take this.”

Legend of Zelda ButtonsNew pin-back buttons from Pink Toe Press.

Confession time: I’m a Gamer Girl. I really love video games and have an especially soft soft-spot for the Legend of Zelda franchise. I still remember the day that my parents got me a Gameboy that came with the Legend of Zelda Link’s Awakening game cartridge. I was completely unable to put the game down for days, captivated by the characters and puzzles. After that came my first love, the Nintendo 64. My siblings and I didn’t leave the house for days and we barely slept or ate. All we did was play Mario Kart or similar racing games for hours and hours. But then…Then came the Legend of Zelda Ocarina of Time. I must have logged 100’s of hours on that game. I could go on and on. But… “Hey Listen!”


Hylian Shield Buttons

The Hylian Shield buttons are a fun new addition to Pink Toe Press.

That brings me from the true topic of this post…Pink Toe Press’ newest addition: Retro Zelda Hylian Shield Buttons. With designs drawn by yours-truly and made into 1-inch pin-back buttons, they are the perfect addition to your bomb bag or tunic! I currently have designs from Link’s Awakening and a Link to the Past as well as the Ocarina of Time and Majora’s Mask. Each shield was hand-drawn and colored. They were a lot of fun for me to make and I look forward to making similar projects again in the near future! Stay tuned!

Here is a sneak peek of some of the new items you’ll be able to find at Pink Toe Press:

Legend of Zelda Shields

Can you guess what these are?

Are you…STUCK?

(they’re stickers…coming soon!)